Showing posts with label Railblaza. Show all posts
Showing posts with label Railblaza. Show all posts

Sunday, 10 November 2013

Snapper from the Hobie Kayak?

I Decided to have an early fish with local Yaker and friend Dave Tingey alias 'Tingles' at a local spot near Adelaide. It was decided upon that we would meet early next morning to see if there were any Snapper around as the ban was in place the following week. This is to help Snapper stocks not being interrupted during their annual spawning season. 'Tingles' had an early appointment and couldn't get there until around 6 so I decided I would start without him.

It was around 5.20am when I reached the launch site, there was little moon and it was very dark. I wanted to turn the car around so I could back the trailer near the ramp which is quite steep so I proceeded to turn the car around when it came to a noisy halt! What had I done! I've ran over something. On inspection I had gone over the edge or the ramp and the left front wheel was in the air, the underside of the car flat on the ground. ARRGGGG!! I had forgotten about the steepness of the ramp and was also worried as the yak was still in the middle of the road. After laying some rubber, literally, I was humiliated and embarrassed at what had happened, must have sounded like a yobbo!
After I had the car where it should be I proceeded to get things ready without any more incident, phew.

The water sounded quite calm as it was still dark, I wouldn't have launched if it wasn't.
I checked all the safety gear, put on the PFD, turned on the Railblaza Navi light and also the LED Navilight Port/Starboard, no way I'm taking chances in the dark and these lights are very bright, great visibility and totally waterproof.

To make it easy with launching, Dave had previously showed me a great tip. Have the mirage drive clipped with a bungee so to is flat under the hull for launching but you can still use it once you peddle. I did this without any dramas and relaxed the bungee once in safe water which was over the first breakers. I didn't actually realise from the shore but there was a bit of swell but nothing to worrying and proceeded to anchor on what I thought looked good, nice broken bottom and around 5m of water.

This Mulloway was caught using the same plastic earlier in the year, see post HERE.
Today I was trying bait and plastics so I threw out my first rig, a whole pilchard on 2 snooded hooks, and no sinker as there wasn't much water movement into the darkness, let out some line, double-checked the drag, put it in the rod holder and locked it in place.

I then started to berley which consisted of chopped up pieces of the 2kg of pilchards that I had prepared the night before.

My next rig was the plastic so after smearing on some SFactor onto the Pilly Flickbait I again tossed it into the darkness and started to work the lure.

"I was fishing for over 1/2 an hour without a touch, the sun had started to creep over the hills and I could see 'Tingles' in the distance making his way over, great I thought, at least one of us should get a Snapper".

We started to fish together, burleying at intervals but with no results. I then started to try some different tactics, tied on my ever reliable sinking minnow to see if there was any snook or salmon around but even that didn't get a hit. Try for some squid I thought, so I put on the jag and flicked it as far as I could.
I left it for quite a while as the wind was picking up and the water was getting a little sloppy but managed to get one.

This was only a small one, There was some nice ones out there.


After this had happened my Snapper rod came up tight (which I had left in the holder) and I thought you ripper I'm on, lend back on the rod and set the hook, whatever it was took a bit of line and then nothing. Drat a Stingray I thought as I put as much pressure on the 'ray' as I could, the rod had a serious bend in it and I was putting some major hurt on the ray but it wasn't budging, much to the amusement of Tingles. I gave up after what seemed at least 10 minutes and had to break it off but at least I knew my reel and line (15lb) was more than up to the challenge and the knots held.

Trying to put some hurt on the Ray.

Over the course of the morning of flicking it right out leaving it till it was right near the bottom and hopping it back I managed a total of 12 Squid, while trying for some whiting as I had given up on the Snapper idea I also managed a few others, a Leatherjacket and a Wrasse which I had heard tasted all right - they were wrong!

Not to bad considering.

Dave also had some success and we trolled along the coast over to the jetty and back again where I dropped a good Snook while trolling a squidgy bloodworm wriggler.

It got quite sloppy and it's always good to make sure you can be seen on the water, These flags certainly help when the swell is getting up.

Dave alias 'Tingles'  in the swell, great idea to be as visible as possible.
After a safe beach landing we had a breather and then it was the horrid task of getting the yaks over the soft sand up the steep ramp to the cars and I only had my normal trolley. Thankful Dave was able to help me over the sand, once we got them up there we had to catch our breath - well I did anyway.

So although I didn't end up getting my target fish of snapper, by trying a few different things still ended up catching a feed, having great time with a mate and getting out on the water, good times all-round.

Future blogs will be added frequently so please bookmark the page, thanks for reading.






Friday, 2 August 2013

DIY How to 'blaze' the Hobie Pro Angler with Railblaza - Tidy Sounder cables


The Project. This is really basic and not really a DIY but I thought I would share it anyway.
I really wanted to tidy up the sounder cords - I hate cords! I am sitting at a computer every day for my job and the power cords etc. They drive me nuts!

The Plan. Simply tidy them up. This was achieved by firstly filing a bit of a notch in the back of the rotating platform to help the cords sit nicely. I also added a stick on cable guide and the cables run underneath, nice and tidy.

The next step was to simply put cable clips as out of the way as possible to house the cabling, these are quick release and if I want to change the sounder position its an easily achievable, I just put the cables in certain clips.
starport fixing plate underneath to add extra strength.

This helps keep the cords away from hooks jigheads etc.



By using clips it keeps the cords out of the way and if the sounder needs to e moved they are opened quickly. The sounder can go on both sides of the kayak and also at the front sail mount.

Parts used or shown.

Starports


Adjustable platform

Railmount - 19-25


Blogs will be added frequently so please bookmark the page, thank's for reading.


You can check out the products videos etc at http://www.railblaza.com

*product images taken from Railblaza catalogue - download here: http://www.railblaza.com/uploads/Products/RB%20Cat%202013%20Catalogue%20Web.pdf









Tuesday, 30 July 2013

DIY 'blazing' the Hobie with Railblaza

I wanted to write a bit of a guide on how and why I have fitted my Hobie Pro Angler the way I have with the Railblaza system. My main consideration was to make it as functional as possible and I am very happy with the results.
Please check out my other blogs to see the full list.

I love the way if I want to swap things around it is totally achievable - even putting the sounder up the front which I have just realised and when I don't need items, or when they're not in use, they can all be stowed away, easily and quicky.

I have 5 star ports fitted on the yak: 2 on the rails 2 on the runner boards and one at the stern.

This gives me all the locations in which I need to be able to access my gear.

Project 1. recessed starports.
To make thing nice and tidy the starports are recessed and I have also added the 2 black mounts (supplied with the starports) underneath to give it a bit more stability, although probably not needed (but it covered up the bolts nicely) :) It also helps keep it streamlined and there are less things for line to catch on. Just follow the instructions on the packaging to achieve this, measure twice cut once as they say, but MAKE SURE if you have a PA you put it close enough to the edge so it clears the hull (Thanks Neil Hutchins for that great advice!)

This is at the stern on the rudder hatch.

I have used adhesive cable clips to keep the sounder cables nice and tidy and also taped the two cables together, this is the rotating platform which is fantastic for sounders, cameras etc.





The Railblaza System.
The next lot of photos show the true versatility of the Railblaza system in use, all the products could be mounted in each of the starports (apart from the sounder at the stern - but what would be the point of that). This is very handy depending on the position of the sun e.g. glare on the sounder and also which side I fish from to what is mounted where.









Parts used.
Navilight


Rod holder

Rotating platform

Mobi adjustable device holder

Railmount - 19-25

Extenders

TracPort Dash 350

Adjustable platform

Starports


Blogs will be added frequently so please bookmark the page, thank's for reading.


You can check out the products videos etc at http://www.railblaza.com

*product images taken from Railblaza catalogue - download here: http://www.railblaza.com/uploads/Products/RB%20Cat%202013%20Catalogue%20Web.pdf